reading SNMP Values

Page: 12 > Showing page 1 of 2
Author
hde
New Member
  • Total Posts : 6
  • Reward points: 0
  • Joined: 2020/02/14 02:26:30
  • Status: offline
2020/02/14 04:30:55 (permalink)

reading SNMP Values

We are useing the SNMP Module to Read and compare Values for Alerting. Works fine for UP and DOWN.
Is there any way (keyword) to include the value read in a SMS Message ?
 
thanks
#1

10 Replies Related Threads

    IPSentrySupport
    Support Guy
    • Total Posts : 2072
    • Reward points: 0
    • Joined: 2006/05/16 21:55:52
    • Status: offline
    Re: reading SNMP Values 2020/02/14 11:09:05 (permalink)
    Enable "Return Full Results" in the addin
    See: http://www.ipsentry.com/htmlhelp70/IPSENTRY/addins/snmpmon.index.htm#host_ReturnFull
     
    You can then use the %%mach.resultinfo%% keyword in the email alert.
    Note the result returned is not just a value since the add-in can monitor multiple objects and filters.  It will contain the filter details, thresholds, and read value or failure cause.
     
     

    ---
    IPSentry Support
    RGE, Inc.
    http://www.ipsentry.com
    http://forum.ipsentry.com

    IPSentry® is a Registered Trademark of RGE, Inc.
    #2
    hde
    New Member
    • Total Posts : 6
    • Reward points: 0
    • Joined: 2020/02/14 02:26:30
    • Status: offline
    Re: reading SNMP Values 2020/02/14 12:11:20 (permalink)
    Full Result ist enabled
    on first OID we "must be within range" (200-410)  and %%mach.resultinfo%% is the OID  (1.3.6.1.4.1.28634.16.2.8195)
    on the second OID, we use "must be equal to" 0, we get %%mach.resultinfo%% as "No Result Info"
     
     
     
     
    #3
    IPSentrySupport
    Support Guy
    • Total Posts : 2072
    • Reward points: 0
    • Joined: 2006/05/16 21:55:52
    • Status: offline
    Re: reading SNMP Values 2020/02/14 14:12:00 (permalink)
    Are you seeing "No Result Info" on a "LIVE" result or just when you hit "TEST" on the email configuration settings?
    Note that when you hit test on the email configuration, there are no results to actually send.
    The %%mach.resultinfo%% is only populated with the result of the test generating the alert.
     

    ---
    IPSentry Support
    RGE, Inc.
    http://www.ipsentry.com
    http://forum.ipsentry.com

    IPSentry® is a Registered Trademark of RGE, Inc.
    #4
    hde
    New Member
    • Total Posts : 6
    • Reward points: 0
    • Joined: 2020/02/14 02:26:30
    • Status: offline
    Re: reading SNMP Values 2020/02/16 09:13:50 (permalink)
    Full Result ist enabled
    on first OID we "must be within range" (200-410)  and %%mach.resultinfo%% is the OID  (1.3.6.1.4.1.28634.16.2.8195)
    on the second OID, we use "must be equal to" 0, we get %%mach.resultinfo%% as "No Result Info"
     
     
     
     
    #5
    hde
    New Member
    • Total Posts : 6
    • Reward points: 0
    • Joined: 2020/02/14 02:26:30
    • Status: offline
    Re: reading SNMP Values 2020/02/18 02:12:02 (permalink)
    The "LIVE resultinfo only contains the OID "(1.3.6.1.4.1.28634.16.2.8192.0)", not the value, the alert was based upon
    #6
    IPSentrySupport
    Support Guy
    • Total Posts : 2072
    • Reward points: 0
    • Joined: 2006/05/16 21:55:52
    • Status: offline
    Re: reading SNMP Values 2020/02/18 09:03:23 (permalink)
    Please verify below the oid.
    Our results for a failed test (in this case, just a failed attempt) show:
     
    ** FAIL: 1.3.6.1.2.1.1.5: (1.3.6.1.2.1.1.5)
    [Current: ] Timed Out - No Response
     
    If a value is retrieved, it will show the Current value and comparison that triggered it.
    Below, we are looking at a string OID that is not supposed to be equal to "blah" - and it is not.
     
    OK: 1.3.6.1.2.1.1.5: (1.3.6.1.2.1.1.5)
    [Current: Libs] Value is not equal to [blah]
     
    Please ensure that on host settings you do have "Return Full Results" checked.
     

    ---
    IPSentry Support
    RGE, Inc.
    http://www.ipsentry.com
    http://forum.ipsentry.com

    IPSentry® is a Registered Trademark of RGE, Inc.
    #7
    hde
    New Member
    • Total Posts : 6
    • Reward points: 0
    • Joined: 2020/02/14 02:26:30
    • Status: offline
    Re: reading SNMP Values 2020/02/18 13:04:26 (permalink)
    The OID is correct, it's actually the Voltage of a Generator.
    If I do "get Value" or look at the "Current Value" in the Filter config, it shows the correct number.
    Just the %%mach.resultinfo%% in the SMS generated shows the OID only. I am looking to get the current Value in the SMS
     
    thanks
    #8
    IPSentrySupport
    Support Guy
    • Total Posts : 2072
    • Reward points: 0
    • Joined: 2006/05/16 21:55:52
    • Status: offline
    Re: reading SNMP Values 2020/02/18 16:51:46 (permalink)
    Is it just in SMS (Short Message) or in email?   SMS may truncate depending on settings.
     

    ---
    IPSentry Support
    RGE, Inc.
    http://www.ipsentry.com
    http://forum.ipsentry.com

    IPSentry® is a Registered Trademark of RGE, Inc.
    #9
    hde
    New Member
    • Total Posts : 6
    • Reward points: 0
    • Joined: 2020/02/14 02:26:30
    • Status: offline
    Re: reading SNMP Values 2020/02/19 01:59:33 (permalink)
    Allright, we are getting closer.
    in EMail, %%mach.resultinfo%% returns:
    : (1.3.6.1.4.1.28634.16.2.8195)
    [Current: 237,00] Is not between [220] and [230]
     
    on SNMP-Walk and in the Filter, the Value is 238, so useing %%mach.trimres_l38%% returns:
    237,00] Is not between [220] and [230]
     
    With SMS, the %%mach.resultinfo%% seems to get truncated after 8195), maybe a <CR> ?
    Length is set to 160.
    Anyhow, is there a way to just put the read Value (237) in the Message?
     
    #10
    Page: 12 > Showing page 1 of 2
    Jump to:
    © 2020 APG vNext Commercial Version 5.5